SARK-100 MINI60 HF ANT SWR Antenna Analyzer Meter 1-60 Mhz Tester For Ham Radio

Description

Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
SARK-100 MINI60 HF ANT SWR Antenna Analyzer Meter 1-60 Mhz Tester For Ham Radio
Popular
Popular
Product Introduction
Description:
1.Type 1 (SARK100 Antenna Analysis)
This is a SWR Analyzer for ham hobbists.
Frequency Generation & Control: 1 - 60 Mhz
Source impedance: 50 Ohms
Stability: +/- 100 ppm
Spectral Purity: Harmonics down >- TBD dB beyond 60 MHz
Step Size: User configurable increments of 100 Hz, 1 kHz, 10 kHz, and 100 kHz
Usable Measurement Range:SWR: 1.0 to 9.99
Impedance: approx. 5 to 2000 ohms
RF Output: Adjustable: 2.0 Volts pp (typ)
Power supply: Powerd by External: 12 to 15 Volts DC, 500mA
Controls: Pushbuttons (5): "Mode", "Band", "Config", "Scan", "Up", "Down"
Switch: "Power On"
Connectors: RF Out: BNC
USB: Mini-B receptacle
External power: 2.1mm Power Jack (center pin positive)
Applications:
Measure antenna electrical parameters: SWR, impedance (resistance +
reactance), capacitance, inductance
Measure feedpoint impedance
Measure ground loss
Adjust antenna tuners and determine loss
Measure inductors and capacitors
Measure coax transmission line (SWR, length, velocity factor, approximate Q
and loss, resonant frequency, and impedance)
Measure and determine optimum settings for tuning stubs: SWR, approximate
Q, resonant frequency, bandwidth, impedance
Determine characteristic impedance of transmission line
Determine length of ? and ? wave phasing lines
Coaxial Cable Loss
Determine antenna tuner loss
Measure balun loss
Measure inductor Q
Estimate quartz crystal parameters
Measure magnetic loop resonance and SWR
Operation button definitions:
Mode: selects operation mode: impedance(default), complex impedance, capacitance, and inducatance
BAND: select band from any of the available bands: 160M to 6M
CONFIG: Provides menu for configurations and extended functions: PC Link, step size setting, suspend timeout setting, calibration, and software upgrade
SCAN: pressing this control initiates a scan of frequencies of the selected BAND. Scan exits to impedance mode showing the 2:1 bandwidth and the resonant point o the antenna
CAN(up): increase frequency and used to cancel operation for CONFIG menu
VAL(down): decrease frequency and used to validate operation for CONFIG menu
Package Included:
1 x ANT SWR Antenna Analyzer Meter For SARK100 Ham Radio Hobbist
2.Type 3(MINI60 SARK100 with No bluetooth)
Hardware:
Precise and self-calibrating reflectometer design measures forward and reflected signals and impedance data
Display 2x16 with optional backlight
Precision DDS signal generator (AD9851) used as signal source
USB port connects to PC for field-upgradeable software and uploading of real-time measurement data
Buzzer
Operation:
Manual control option displays SWR and complex impedance at selected frequencies
Automatic scanning results displayed as frequencies of lowest SWR and complex impedance
Power saving modes
Multi-point calibration for better accuracy
Instrument Capabilities:
Measure antenna electrical parameters: SWR, impedance (resistance + reactance), capacitance, inductance
Measure feedpoint impedance
Measure ground loss
Adjust antenna tuners and determine loss
Measure inductors and capacitors
Measure coax transmission line (SWR, length, velocity factor, approximate Q and loss, resonant frequency, and impedance)
Measure and determine optimum settings for tuning stubs: SWR, approximate Q, resonant frequency, bandwidth, impedance
Determine characteristic impedance of transmission line
Determine length of ¼ and ½ wave phasing lines
Coaxial Cable Loss
Determine antenna tuner loss
Measure balun loss
Measure inductor Q
Estimate quartz crystal parameters
Measure magnetic loop resonance and SWR
Specifications:
Frequency Generation & Control:
1 - 60 Mhz
Source impedance: 50 Ohms
Stability: +/- 100 ppm
Spectral Purity: Harmonics down >- TBD dB beyond 60 MHz
Step Size: User configurable increments of 100 Hz, 1 kHz, 10 kHz, and 100 kHz
Usable Measurement Range:
SWR: 1.0 to 9.99
Impedance: approx. 5 to 2000 ohms
RF Output:
Adjustable: 2.0 Volts pp (typ)
Power supply:
External: 12 to 14 Volts DC, 500mA
Controls:
Pushbuttons (5): "Mode", "Band", "Config", "Scan", "Up", "Down"
Switch: "Power On"
Connectors:
RF Out: BNC
USB: Mini-B receptacle
External power: 2.1mm Power Jack (center pin positive)
Package Included:
1 x Antenna Analyzer (as the picture)
3.Type 4(MR100 Shortwave Antenna Analyzer)
Can test a standing wave, resistance, capacitance, etc
Can connect the computer to do the antenna and other graphic analysis
Test frequency: 1-60 m
Size: 90 mm * 82 mm * 30 mm (super light super mini)
Power supply: 12 v
Joint: Q9 head
Package Included:
1xMR100 Shortwave Antenna Analyzer Meter Tester For Ham Radio DC 12V Q9 Head
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
SARK-100 MINI60 HF ANT SWR Antenna Analyzer Meter 1-60 Mhz Tester For Ham Radio
Product Introduction
Description:
1.Type 1 (SARK100 Antenna Analysis)
This is a SWR Analyzer for ham hobbists.
Frequency Generation & Control: 1 - 60 Mhz
Source impedance: 50 Ohms
Stability: +/- 100 ppm
Spectral Purity: Harmonics down >- TBD dB beyond 60 MHz
Step Size: User configurable increments of 100 Hz, 1 kHz, 10 kHz, and 100 kHz
Usable Measurement Range:SWR: 1.0 to 9.99
Impedance: approx. 5 to 2000 ohms
RF Output: Adjustable: 2.0 Volts pp (typ)
Power supply: Powerd by External: 12 to 15 Volts DC, 500mA
Controls: Pushbuttons (5): "Mode", "Band", "Config", "Scan", "Up", "Down"
Switch: "Power On"
Connectors: RF Out: BNC
USB: Mini-B receptacle
External power: 2.1mm Power Jack (center pin positive)
Applications:
Measure antenna electrical parameters: SWR, impedance (resistance +
reactance), capacitance, inductance
Measure feedpoint impedance
Measure ground loss
Adjust antenna tuners and determine loss
Measure inductors and capacitors
Measure coax transmission line (SWR, length, velocity factor, approximate Q
and loss, resonant frequency, and impedance)
Measure and determine optimum settings for tuning stubs: SWR, approximate
Q, resonant frequency, bandwidth, impedance
Determine characteristic impedance of transmission line
Determine length of ? and ? wave phasing lines
Coaxial Cable Loss
Determine antenna tuner loss
Measure balun loss
Measure inductor Q
Estimate quartz crystal parameters
Measure magnetic loop resonance and SWR
Operation button definitions:
Mode: selects operation mode: impedance(default), complex impedance, capacitance, and inducatance
BAND: select band from any of the available bands: 160M to 6M
CONFIG: Provides menu for configurations and extended functions: PC Link, step size setting, suspend timeout setting, calibration, and software upgrade
SCAN: pressing this control initiates a scan of frequencies of the selected BAND. Scan exits to impedance mode showing the 2:1 bandwidth and the resonant point o the antenna
CAN(up): increase frequency and used to cancel operation for CONFIG menu
VAL(down): decrease frequency and used to validate operation for CONFIG menu
Package Included:
1 x ANT SWR Antenna Analyzer Meter For SARK100 Ham Radio Hobbist
2.Type 3(MINI60 SARK100 with No bluetooth)
Hardware:
Precise and self-calibrating reflectometer design measures forward and reflected signals and impedance data
Display 2x16 with optional backlight
Precision DDS signal generator (AD9851) used as signal source
USB port connects to PC for field-upgradeable software and uploading of real-time measurement data
Buzzer
Operation:
Manual control option displays SWR and complex impedance at selected frequencies
Automatic scanning results displayed as frequencies of lowest SWR and complex impedance
Power saving modes
Multi-point calibration for better accuracy
Instrument Capabilities:
Measure antenna electrical parameters: SWR, impedance (resistance + reactance), capacitance, inductance
Measure feedpoint impedance
Measure ground loss
Adjust antenna tuners and determine loss
Measure inductors and capacitors
Measure coax transmission line (SWR, length, velocity factor, approximate Q and loss, resonant frequency, and impedance)
Measure and determine optimum settings for tuning stubs: SWR, approximate Q, resonant frequency, bandwidth, impedance
Determine characteristic impedance of transmission line
Determine length of ¼ and ½ wave phasing lines
Coaxial Cable Loss
Determine antenna tuner loss
Measure balun loss
Measure inductor Q
Estimate quartz crystal parameters
Measure magnetic loop resonance and SWR
Specifications:
Frequency Generation & Control:
1 - 60 Mhz
Source impedance: 50 Ohms
Stability: +/- 100 ppm
Spectral Purity: Harmonics down >- TBD dB beyond 60 MHz
Step Size: User configurable increments of 100 Hz, 1 kHz, 10 kHz, and 100 kHz
Usable Measurement Range:
SWR: 1.0 to 9.99
Impedance: approx. 5 to 2000 ohms
RF Output:
Adjustable: 2.0 Volts pp (typ)
Power supply:
External: 12 to 14 Volts DC, 500mA
Controls:
Pushbuttons (5): "Mode", "Band", "Config", "Scan", "Up", "Down"
Switch: "Power On"
Connectors:
RF Out: BNC
USB: Mini-B receptacle
External power: 2.1mm Power Jack (center pin positive)
Package Included:
1 x Antenna Analyzer (as the picture)
3.Type 4(MR100 Shortwave Antenna Analyzer)
Can test a standing wave, resistance, capacitance, etc
Can connect the computer to do the antenna and other graphic analysis
Test frequency: 1-60 m
Size: 90 mm * 82 mm * 30 mm (super light super mini)
Power supply: 12 v
Joint: Q9 head
Package Included:
1xMR100 Shortwave Antenna Analyzer Meter Tester For Ham Radio DC 12V Q9 Head
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.